Slag Crusher Manufacturer In India

Abstract

Damage To The Hydraulic Pump Of The India Slag Crusher Air Incorporation Air mixing refers to the phenomenon that air bubbles are dispersed in the system working fluid. The system using hydraulic oil can find bubbles in the fuel …

Damage To The Hydraulic Pump Of The India Slag Crusher

Air Incorporation

Air mixing refers to the phenomenon that air bubbles are dispersed in the system working fluid. The system using hydraulic oil can find bubbles in the fuel tank, and in severe cases, the oil can be emulsified. When such a bubble is compressed to the outlet of the hydraulic pump of the India Slag Crusher, a rupture effect is generated, causing the metal side of the pressure side plate, the wear side plate and the like to be peeled off near the fracture point, and causing an extremely high temperature there. When air is mixed in, noise will appear, and this noise will increase as the pressure increases. Air mixing can also cause malfunction of various components (pressure swing, etc.) and actuator crawling.

The possible way of causing air to enter the internal pressure of the India Slag Crusher hydraulic pump is mainly caused by poor oil seal and hydraulic pump inlet pipeline, and the system return oil pipeline, cylinder shaft seal and other parts are not tightly sealed, and the air is brought in. Therefore, it is necessary to pay great attention to the installation of the hydraulic pump inlet joint of the India Slag Crusher, the sealing oil of the system oil return and the drain pipe joint, and the sealing rubber gasket and the rubber ring.

Cavitation

Cavitation refers to a localized gasification that occurs in a fluid when the pressure is reduced below the saturated vapor pressure. Simply put, this cavitation can be caused when the working fluid is not completely filled and should occupy space. The noise caused by cavitation is roughly similar to the noise of air mixing. The cause of cavitation is mainly because the hydraulic pump running speed of the India Slag Crusher is too fast, the flow rate of the liquid pump of the India Slag Crusher is too large, the suction pipe is too long, or the working liquid is too sticky, so when installing the hydraulic pump of the India Slag Crusher, the suction pipe is installed. No hoses that are easily deformed.

Working Liquid Pollution

Working liquid contamination refers to the presence of solid mechanical impurities, moisture, gases, debris, etc. in the working fluid. The mixing of mechanical impurity particles in the working fluid will sharply increase the friction and wear of the parts. In severe cases, the card may be stuck, overheated, and the drive shaft may be broken. The throttle gap may also be blocked to cause the component to malfunction or fail. Therefore, the working fluid has a certain Cleanliness requirement.

Control the pollution of the hydraulic system to meet the specified cleanliness requirements. When replacing the hydraulic pump of the India Slag Crusher, check the filter at the same time. If the filter is found to have pollutants, look for the source of pollution and eliminate the source of the pollution. Replace the filter or replace the hydraulic oil or bypass filtration. Use the oil filter to filter the liquid in the tank regularly or irregularly, filter out the impurities in the working fluid, and analyze the pollutants to find the cause. And eliminate the source of pollution.

Clean micron oil can be installed on the outlet of the India Slag Crusher hydraulic pump or on the return line of the return tank to achieve cleanliness. The control system is equipped with 35m (filter paper filter), high-pressure system with 10m (filter or filter paper filter), and the general hydraulic system with 20m filtration accuracy (filter paper filter). If the filter is omitted, although it can work for a short time, it always has a hidden trouble and will malfunction at any time.

Pre:

Submit Demands Online

Other Case

Mobile Jaw Crusher

Mobile Jaw Crusher

Mobile jaw crusher manufacturerd by SBM Machinery is widely used in portable stone crushing plant, quarrying deposits, mining and construction industry.

M Sand Manufacturing Machine

M Sand Manufacturing Machine

M Sand Manufacturing Machine is also called Sand Making Machine, which is suitable for the soft or hard and extremely hard materials crushing, plastic, are widely used in all kinds of ores.

Copper Beneficiation Process

Copper Beneficiation Process

Copper Beneficiation Process workers for all kinds of Copper and Copper polymetallic ore has carried on the detailed research, especially the study of low grade Copper ore with a lot of work, and achieved a number of scientific and technological achievements.